Re: virtual connect Port Status INCOMPATIBLE
You are plugging the wrong SFP into the ports is the simple answer.Are you putting FC SFP in LAN ports or vice versa?Are you plugging 16GB SFP into 8GB ports?
View ArticleRe: Ports used for Accelerated ISCSI
Q: Can I use any uplink port for accelerated ISCSI, or just Port X5?A: I dont think this matters. iSCSI is a network VLAN so should just work down any uplink Q: If I can use more than one port from...
View ArticleRe: HP Virtual Connect Manager Ethernet network problem, one nic connection...
Is All_Prod multiple VLANs?Have you setup VLAN tagging correctly on the blade?
View ArticleRe: VC FF 20/40 and Stacking
I wouldn't go with stacking the enclosures unless you really must do to get uplink bandwidth, OneView does not support stacked enclosures so I expect this method to be used less and less by people...
View ArticleRe: Guide to Beginners
The "Virtual Connect Cookbooks" are good. Do an internet search, just be mindful of the VC versions they apply to. -Bob
View ArticleWhat is Subordinate VC Module ?
Hello,For one of my customer, we have the following config - 1 * Primary Virtual Connect Module 1 * Backup Virtual Connect Module 2 * Subordinate Virtual Connect Module Presently all are running with...
View ArticleRe: What is Subordinate VC Module ?
In a Virtual Connect environment there are two VC modules that run the Virtual Connect Manager. The primary and the secondary as you have noted. Any other VC module in that domain would be considered...
View ArticleRe: What is Subordinate VC Module ?
Thanks for the reply !! Instead of automatic sequence, we are thinking about running the reboot in manual mode, using the following command -vcsu -a update -i <enclosure OA IP> -u <OA...
View ArticleVCM GUI Opens with Blank Windows
Hello!My Infra's VCM GUI was earlier getting stuck at 4% while loading libraries. Now, after following this HPE Article, the GUI does load up, but in various sections I am getting blank placeholders -...
View ArticleSimple VCM Stacking Link Configuration Question
I have what I think is a simple VMC stacking link question:We have three c7000 enclosures.Currently, we have our Enclosure1 stacked with Enclosure2 as follows:ENC1/BAY1/X6 to ENC2/BAY1/X6ENC1/BAY2/X6...
View ArticleRe: Simple VCM Stacking Link Configuration Question
Your diagram looks right. You dont say what VC version, but for this, its basically all the same anyways. Here is a document for 4.20 you can reference for more...
View ArticleFirmware Update for Virtual Connect Modules
Hello !Need help in upgrading firmware on my Virtual Connect Modules. Infra : In the VCSU healthcheck results, we get one “primary”, one “backup”, and 2 “subordinate” modules. Question: To update...
View ArticleRe: Firmware Update for Virtual Connect Modules
You will update all in a single session, but you can control the activation (reboot) order.
View ArticleRe: Simple VCM Stacking Link Configuration Question
I am at VC firmware 4.5 on all six VCMs and all six OA's for that matter.While I did not see my exact scenario on the referrenced document, it is a nice document to have as it explains a great deal on...
View Articlec7000 - OA, VC and ILO re-ip question
hii need to re-ip our C7000 chassis, OA, ILO and VC (Flex) and im wondering if anybody here has done it before and could share some thoughts. ILO is easy, im not concerned about that.more concerned...
View ArticleRe: VCM GUI Opens with Blank Windows
Got this fixed by following the second workaround mentioned in this link > > http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c04677033
View Articlec7000 - Unexpected behaviour for Virtual Connect Manager
Hi,I'm facing some problems for OnBoard Administrator / Virtual Connect Manager configuration and I have not been able to address them. Let me explain: I have a C7000 enclosure configured that have...
View ArticleVC supported Upgrade path
Hey gus, I'm planning an upgrade from VC 3.51 and 4.01 to 4.45.There are Flex-10 Enet and 8GB 20 Port FC modules in the enclosures. I'm a little confused on the upgrade path. In the 4.45 release notes...
View ArticleVC SAN FC migration
Hello,i am facing an issue, after migration of FC SAN to new SAN switch, all paths from this VC are down. Previously there was on SAN switch and two FC cables from C7000 VC-Flex (VC-A and VC-B) were...
View Article
